Repair Tips Repair Tips Repair Tips
Our Parts Investigators are some of the best in the business! That's why we've asked a few of them for some sure-fire repair tips to help you trouble shoot your appliance problems.
|
Refrigerator, Freezer, Water Filter Range Dryer Washing Machine Dishwasher Gas Grill
|
Refrigerator, Freezer, Water Filter
- Replace your water filters at least twice a year to ensure quality water and taste.
Fresh Food Section Too Warm
-Check to see that both fans are running. There is a fan inside the freezer, and one underneath the rear compartment, which cools the condenser on most frost-free units.
-If your fridge has dual controls, be sure the refrigerator air control has not been turned down too far. Check the freezer section for signs of frost on the walls, particularly on the rear and floor panels. Frost would indicate a defrost failure.
-Check the condenser coils in back for dust & debris. This should be done yearly.
Freezer Section Too Warm
-Check to see that the freezer fan is running.
-If your fridge has dual controls, be sure the freezer control has not been turned up too far.
-Check the freezer section for signs of frost on the walls, particularly on the rear and floor panels. Frost would indicate a defrost failure.
-Check the condenser coils in back for dust & debris and check that fan is running there.
-Be sure that food items are not blocking air intakes in freezer. A stuffed freezer can create airflow problems.
Not Cooling at all
-Check to see if anything is running, such as a fan. If not, power can be interrupted at the defrost timer or the cold control. A proper check with a meter can determine which it is.
-The defrost timer can be manually advanced to see if it is stuck, and to verify that the heaters are working in the freezer. (Heaters only work if temp is below 28 degrees F.)
-If the compressor is running, but no cold air is coming from the freezer, then you can assume that you have a sealed system problem, and will need professional help.
Range
- When replacing Range top burners, plug in type, always check for burnt contacts in burner receptacle. To be safe replace receptacle with top burner.
-If your electric surface burners are not heating as normal, lightly sandpaper the contacts on the element and the block they plug into. Safety first, unplug your stove. If service is still impaired, replace blocks first, then the coiled element.
- To keep an old stove looking new, use Maytag cooktop cleaner. We also carries a large range of touch up paints to repair nicks and scratches.
Dryer
- Replace old plastic dryer venting with safe durable smooth metal venting to prevent a fire. Plastic venting can catch the lint that can cause a fire. Safe metal venting is recommended by all manufactures and will prevent possible fires.
- Don't forget to replace the idler pulley when changing the belt on your dryer
-Is your dryer not heating as fast? If so, remove the venting and run a cycle...if it helps you may need to replace your venting!
Washing Machine
- When changing the belts on your Maytag washer change the motor slide kit...This will let the spin cycle get up to speed and get the maximum amount of water out of your clothes and save on the drying time.
Dishwasher
- It's a good idea to clean out your dishwasher once every six months with Glisten. This removes all the build up and leaves your machine lemony fresh.
- Does the inside of your dishwasher appear to have a discolored look on the tub sides & on the dish racks? Product # 18001059 will completely clean the inside of the tub, dish racks and all of the water carrying parts including the inside of the pump, hoses and recirculating parts that carry water.
- Maytag dish rack repair kits can save you from having to buy costly new racks. Complete with replacement tine tips and adhesive sealant to repair and stop the rust. The kits come in copper, stainless steel, gray, white and blue.
- For most dishwashers, the interior is normally self-cleaning. However, in very hard water areas lime deposits as well as some discoloration of filming may occur. Remove it with a damp cloth and a mild scouring powder. In severe cases, set the empty dishwasher on "RINSE AND HOLD CYCLE." After the dishwasher has filled, add 1/2 cup of white vinegar to the water. Allow the dishwasher to complete the cycle. DO NOT USE A DETERGENT!
Gas Grill Care Tips
Do
... After cooking, turn grill to high for a few minutes to burn off excess grease deposits. Then turn off gas knob at the tank.
... Cook with hood down when possible. It is generally faster and more efficient. Trapped smoke adds to the flovor.
... Have proper tools, tongs, mittens and hot pads ready prior to removing foods.
... Trim excess fat from meats to minimize flare-ups.
... Let grill cool before removing any parts for cleaning.
... Be sure to replace parts correctly after cleaning.
... Be careful of the control valve setting.
... Note the grill model number on your instructions and keep the instructions and parts list in a convenient place.
... Raise the hood before lighting the burner.
Do Not
... Install or use a gas grill inside any building.
... Use plastics or untempered glass utensils on the grill.
... Attempt to move an aluminum foil pan while it is hot. Let it cool first before moving it.
... Cover or block any air openings in the bottom of the grill with foil.
... Wear long, loose flowing clothes around the grill. Long flowing hair is easily ignited especially by unexpected flare-ups.
... Tie hair back or wear a scarf.
... Use caustic materials, i.e. lye, to clean grill parts.
... Squirt water on the burner in attempt to control flaring. It turns to steam and can shorten burner life.
... Put food on the grill and leave it unattended or unwatched for long periods. Most fats can catch fire even on the lower setting.
... Clean briquettes in any solution other than boiling water.
... Transport a pre-assembled grill without lying down the hood during transportation.
... Operate the grill without reading the operating instructions.
No Gas or Bad Flame?
•Check venturi tubes and orifice for spider webs.
•On cast iron burners, tip the burner sideways and listen for rust.
•Try adjusting the air shutter.
•Take the burner out of the case and light the gas at the orfice while the valve is in the high position - you should have about a 4" flame shooting out - if not, you may have a bad regulator.
•Try bubble leak around the hose connections - you may have a gas leak.